Gymnastics Balance Beam 8ft Adjustable Height

ASSEMBLY INSTRUCTIONS

Gymnastics Balance Beam 8ft Adjustable Height

ASSEMBLY RATING

The Assembly Rating is a 3-point system that shows the degree of effort needed in assembling a specific product (with 1 being easy and 3 being difficult). It is recommended two people assemble products.

  1. EASY
  2. FAIR
  3. DIFFICULT

REQUIRED TOOLS

  • Allen Key

TOOLS NOT INCLUDED UNLESS STATED

Thank you for your new purchase!

All About Gymnastics hope you will enjoy your new product for many years to come.

As part of our commitment to providing quality products and excellent customer service does not simply end when a purchase is made. We stand behind all of our products and will provide any support needed in order for you to fully enjoy your purchase. Customer satisfaction is highly important and our greatest advertisement when recommended by customers. Because we value your trust in our company, we will do our best to meet your service expectations.

Should you have any assembly related questions, parts replacement requests, comments or suggestions, please feel free to contact All About Gymnastics at any time. To help expedite the service, please have the assembly instructions available, along with your order receipt.

Please complete the below information should you need to contact us.

Product Name  
Date of Purchase  
Order Number  

Contact Information

Email: [email protected]

Telephone: +44 (0) 7927 010 236

ASSEMBLY CARE AND ADVICE

TO ENSURE YOU ENJOY MANY YEARS OF USE WITH YOUR PRODUCT, CORRECT ASSEMBY AND MAINTENANCE ARE REQUIRED.

PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR PRODUCT.

STEP 1. It is highly recommended assembly of your product should be completed near the area for its intended use.

Make sure you have plenty of space to move around your product during assembly.

STEP 2. Position each part correctly and fit screws or bolts into their correct location by hand of using the correct tool.

Only tighten when the step is completed or instructed to do so.

STEP 3. It is advised you assemble your product on card or carpet in order not to damage your product.

Make sure you assemble your product on a flat surface.

STEP 4. ALWAYS have at least 2 people to help assemble products in order to avoid risk of injury, or damage to your product.

STEP 5. When tightening screws or bolts ensure they are aligned in order not to damage the thread.

DO NOT use power tools and do not over tighten.

STEP 6. Store assembly instructions safely for later use. It is recommended regular maintenance should be carried out every 3 months to ensure all parts are tight.

AS WITH ALL EQUIPMENT IT IS THE USERS RESPONSIBILITY TO MAINTAIN EQUIPMENT. PARTS CAN LOOSEN OVER TIME AND YOUR PRODUCT COULD BECOME WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE INJURY.

CONTENTS

Tip. Before you start be sure to lay all your parts out and familiarize yourself with each component ready for assembly.

Read our assembly care advice and follow our instructions step by step.

Components

  • Part A – Button allen key bolt
  • Part B – Washer
  • Part C – Spring washer
  • Part D – Detent pin knob
  • Part E – Beam Leg
  • Part F – Leg mount
  • Part G – Beam mount adjustable
  • Part H – Beam

BEAM (LOW MODE)

STEP 1.

Roll your beam (Part H) onto its back with the fixing holes facing up as shown in the picture below. Tip make sure you have plenty of clear working space to freely work around your beam.

 


STEP 2.

First install the washers onto the bolts in the correct order. Spring washer (Part C) first then washer (Part B) next. As a tip place your beam leg on its side and feed the assembled bolts and washers into the holes of the beam leg.

Once you have done this place the beam leg over the beam and align the bolts with the fixing holes on the beam. Should your washers slip off the bolts inside the leg then the beam leg end caps can be easily removed to retrieve your washers.

Once lined up use the allen key long end to tighten both bolts turning clockwise. Repeat this step for the opposite end of your beam.

Your beam should now be complete and ready for use.

BEAM (HIGH MODE)

STEP 1.

Roll your beam (Part H) onto its back with the fixing holes facing up as shown in the picture below. Tip make sure you have plenty of clear working space to freely work around your beam.

Place your beam mount adjustable leg (Part G) onto the beam aligning the 4 holes with the bracket. Please ensure you fit your adjustable leg bracket with the holes facing in the out position as this is important when the user comes to adjusting the height of the beam.

Now fit your bracket with the parts supplied and tighten the bolts with an allen key ensuring the bracket is securely fastened.

 

STEP 2.

Next steps are to attach the beam leg (Part E) and leg mount (Part F). Place the leg mount (Part F) on top of the beam leg (Part E) and align the 4 holes. Once aligned insert the allen key bolts and washers.

Tighten the 4 allen key bolts with the allen key until all are secured.

Once assembled your beam leg should look like the image below.

STEP 4.

Next slot your assembled beam leg into the adjustable leg you have fitted on the beam. Make sure the screw head is facing in the same direction as the adjustable leg holes as you will need to fit the detent pin knob here (Part D).

Your beam leg should look like this once fitted

STEP 5.

Adjust the beam leg to your desired height then screw in the detent pin knob to secure the leg in position turning clockwise. Repeat this step for the opposite end.

STEP 6.

We highly recommend a final visual inspection is carried out with your beam, checking all bolts (fastens) are properly secured before use. Once complete you are ready to rotate your beam on its side and stand it upright on its legs.

ASSEMBLY IS NOW COMPLETE

WARNING

  • Serious injury (including permanent paralysis or death) could result from any activity involving motion, rotation or height.
    • All users of this equipment assume this risk of serious injury.
    • Mats and pits cannot and do not eliminate hazards.

Safety Instructions

ALWAYS:

  1. Consult an instructor prior to use.
  2. Use equipment ONLY under the supervision of trained and qualified instructors.
  3. Use equipment with trained spotters and the proper spotting equipment.
  4. Check equipment before use for proper positioning, ensure it is placed on a flat surface; equipment can move during use.
  5. Assure that all equipment fixings are secured and tight.
  6. Follow progressive learning pattern. Assure basic skills are achieved before attempting more advanced skills.
  7. Use equipment ONLY when all hard-exposed surfaces are protected with proper mats.

DO NOT use the apparatus with damaged, worn or missing parts.

DO NOT allow more than one person at a time to use the equipment.