Horizontal Junior Gymnastics Bar

ASSEMBLY INSTRUCTIONS

Horizontal Junior Gymnastics Bar

ASSEMBY RATING

The Assembly Rating is a 3-point system that shows the degree of effort needed in assembling a specific product (with 1 being easy and 3 being difficult). It is recommended two people assemble products.

  1. EASY
  2. FAIR
  3. DIFFICULT

REQUIRED TOOLS

  • Screwdriver
  • Allen Key

TOOLS NOT INCLUDED UNLESS STATED

Thank you for your new purchase!

All About Gymnastics hope you will enjoy your new product for many years to come.

As part of our commitment to providing quality products and excellent customer service does not simply end when a purchase is made. We stand behind all of our products and will provide any support needed in order for you to fully enjoy your purchase. Customer satisfaction is highly important and our greatest advertisement when recommended by customers. Because we value your trust in our company, we will do our best to meet your service expectations.

Should you have any assembly related questions, parts replacement requests, comments or suggestions, please feel free to contact All About Gymnastics at any time. To help expedite the service, please have the assembly instructions available, along with your order receipt.

Please complete the below information should you need to contact us.

Product Name  
Date of Purchase  
Order Number  

Contact Information

Email: [email protected]

Telephone: +44 (0) 7927 010 236

ASSEMBLY CARE AND ADVICE

TO ENSURE YOU ENJOY MANY YEARS OF USE WITH YOUR PRODUCT, CORRECT ASSEMBY AND MAINTENANCE ARE REQUIRED.

PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR PRODUCT.

STEP 1. It is highly recommended assembly of your product should be completed near the area for its intended use.

Make sure you have plenty of space to move around your product during assembly.

STEP 2. Position each part correctly and fit screws or bolts into their correct location by hand of using the correct tool.

Only tighten when the step is completed or instructed to do so.

STEP 3. It is advised you assemble your product on card or carpet in order not to damage your product.

Make sure you assemble your product on a flat surface.

STEP 4. ALWAYS have at least 2 people to help assemble products in order to avoid risk of injury, or damage to your product.

STEP 5. When tightening screws or bolts ensure they are aligned in order not to damage the thread.

DO NOT use power tools and do not over tighten.

STEP 6. Store assembly instructions safely for later use. It is recommended regular maintenance should be carried out every 3 months to ensure all parts are tight.

This image has an empty alt attribute; its file name is image-7.png
WARNING

AS WITH ALL EQUIPMENT IT IS THE USERS RESPONSIBILITY TO MAINTAIN EQUIPMENT. PARTS CAN LOOSEN OVER TIME AND YOUR PRODUCT COULD BECOME WOBBLY AND UNABLE TO SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE INJURY.

CONTENTS

Tip. Before you start be sure to lay all your parts out and familiarize yourself with each component ready for assembly.

Read our assembly care advice and following our instructions step by step.

Components

  • Part A – Button allen key bolt
  • Part B – Washer
  • Part C – Spring washer
  • Part D – Hand knob
  • Part E – Detent pin knob
  • Part F – Base upright support
  • Part G – Bar support
  • Part H – Base connection
  • Part I – Crossbar
  • Part J – Leg end caps
  • Part K – Base leg

 

STEP 1.

First install the base connection (Part H) to the base upright support (Part F). Use the button allen key bolts (Part A), washer (Part B) and spring washer (Part c) and initially tighten with your fingers. Repeat this step when connecting to the opposite side base upright support (Part F).

Once both sides are attached complete this process by finally tightening the button allen key bolts with the required allen key tool.

STEP 2.

Place your base leg (Part K) on the floor and lift step 1 assembly into position and align the bolt holes ready for fixing.

Use the hand knob (Part D) bolts to secure your base upright turning them clockwise until completely secure. Repeat this step for the opposite side.

STEP 3.

First install the crossbar. To do this remove the 4 screw bolts fitted to the crossbar, insert the crossbar (Part I) into each bar support (Part G) identified in Fig. 1 below.

Lay both bar supports (Part G) flat on the ground leaving enough room to fit your crossbar (Part I) in between.

Starting with one bar support and your crossbar slide this over the end aligning the screw holes in the crossbar. Once the holes are aligned with the holes of your bar support you should then refit your screw bolts into your crossbar and bar support. Repeat this step with the opposite side bar support.

STEP 4.

Now that you have your crossbar assembly complete slowly lower the bar supports (Part G) into the base upright supports (Part F) as shown in Fig. 2 opposite.

STEP 5.

You are now ready to set the bars at a safe height suitable for your gymnast.

Once the height is correct and the holes aligned install the detent pin knob tightening clockwise until secure and tight.

STEP 6.

We highly recommend a final visual inspection is carried out with your bars, checking all bolts (fastners) are properly secured before use.

ASSEMBLY IS NOW COMPLETE

General Weight Guidelines 56kg weight limit

WARNING

Serious injury (including permanent paralysis or death) could result from any activity involving motion, rotation or height.

All users of this equipment assume this risk of serious injury.

Mats and pits cannot and do not eliminate hazards.

Safety Instructions

ALWAYS:

  1. Consult an instructor prior to use.
  2. Use equipment ONLY under the supervision of trained and qualified instructors.
  3. Use equipment with trained spotters and the proper spotting equipment.
  4. Check equipment before use for proper positioning, ensure it is placed on a flat surface; equipment can move during use.
  5. Assure that all equipment fixings are secured and tight.
  6. Follow progressive learning pattern. Assure basic skills are achieved before attempting more advanced skills.
  7. Use equipment ONLY when all hard-exposed surfaces are protected with proper mats.

DO NOT use the apparatus with damaged, worn or missing parts.

DO NOT allow more than one person at a time to use the equipment.